Network Cabling Tips
Structured Cabling

Important Tips for NetworkCabling

Important Tips for NetworkCabling

Important Tips for NetworkCabling,Every network support practitioner will agree that faults in network cabling have the potential to ground a company’s communication to a halt.

It doesn’t matter if these problems are transient or intermittent. To discover and correct them, technicians have to take a lot of time only to realize that they are dealing with nothing but simple cabling errors.

Not forgetting that Ethernet data cabling is prone to deterioration. When aged, network cabling is prone to all sorts of errors.

Here are important tips to ensure you have standard, top-notch network cabling:

Important Tips for NetworkCabling

Good Punch or Crimping Tool for Ethernet

An Ethernet network cannot work without there being a proper connection between the data cables and the equipment.

With a faulty connector, you are bound to have all sorts of problems. While the fly-leads usually come with pre-molded connectors extended data cabling in a network does not.

The installer needs a crimping tool to ensure each cable has an RJ-45 connector. The tool should, of necessity be sharp.

Using an old, blunt tool to strip the inner and outer sheath will only damage the vital copper connector. Also, making an off-cable punch will damage the cable.

Although the damage might remain invisible, it will be seen when the connection fails to be fully established.

With these intermittent and transient faults, the performance of the network will be poor. Every time you do something using the network.

It will require the re-sending of the data packet because of loss or corruption along the way. That’s why care must be taken when crimping or punching to provide solid connections.

Take note that RJ-45 connectors come with small wings to solidly hold in place in the Ethernet port. At times, the wings tend to break off resulting in a jammed connector that isn’t sitting properly in place.

In that case, all the Ethernet connectors won’t connect properly resulting in intermittent or transient network errors. If a connector has no wings, simply replace it.

Excellent Splicing For Optical Fibre

A poorly spliced fiber optic connection can cause less than average network performance. It is important that network support learns how to splice, given the continuous preference of Passive Optical Lan over Ethernet.

In fact, copper cabling is steadily being replaced by fiber optic cables. Accurate splicing is key to the working of fiber optic connections.

The problem is that some technicians leave cables slightly out of port. This is the main cause of failure in internal splicing.

At first, the damage may not be obvious and may only become apparent when problems arise in the network. That’s why network connectors must be handled carefully.

Use fiber testers to check for dodgy splices. Once discovered, such splices should be redone to meet the right standards.

Install Network Cables Using Cat6 Standards

Important Tips for NetworkCabling

Cat6 standards have been established for a reason. One of the things you need to watch out for is to not exceed a cable’s bend radius.

Apart from causing interference, this can strain the cable and make it fail. Copper Ethernet cables tend to be noisy near the bent.

This requires lost or corrupted data packets to be resent, thus tampering with network performance. The proper observation of the standards helps to maximize performance while minimizing noise.

when you visit our shop you will get important Important tips for Network Cabling.

Granted, internet speeds have grown exponentially. With speeds of between 100MB and 1GB, it was possible to compromise the standards. Not anymore. Today, speeds range from 10GB to 40GB. You just cannot afford to compromise on the standards.

Importantly, video conferencing and VoIP cannot work on poor-quality connections. The connection must be of high-quality to ensure an above-average performance.

If not, a poor network can compromise the quality of your communication and even cost you money.

Mind the Routing

One of the trickiest parts of networking is installing cable runs. As a rule, avoid putting network cables too close to electrical installations.

If you must, then provide proper shielding to prevent unnecessary interference. Also, don’t leave cables hanging. They are likely to stretch and fail.

All the cables must be channeled through cable trays. It is important to use the flush-mounted wall-boxes. If you don’t, the network can be compromised during cleaning with wet mops and vacuums. If you have swing-frame data cabinets in the user areas, lock them.

Time saving

network cabling installers are often in a rush to finish a piece of work and get going. Many end up accepting cable runs and connectors that aren’t quite up to standard.

Say, an installer notices that several meters of UTP cable runs to surpass the Cat6 standard. He or she chooses to ignore the problem rather than address it.

These time-saving measures worked when internet speeds were lower. Today, it is not possible to get away with that.

 

Leave a Reply

You cannot copy content of this page